Author: Many motorists do not want to spend money on the services of a master - they want to find out for themselves how to connect the radio yourself... Here you need to deal with the following:
- Determine which radio tape recorder is available - regular or non-standard.
- Making the connection itself - we'll look at three common examples.
- Buy, assemble the equipment and tools necessary for connection.
- Learn how to work with wires.
- Imagine a connection diagram for a music player.
- Connect to vehicle with audio preparation.
- Reconnect the old player.
- Connect to a vehicle where there is no player (or installed incorrectly).
- If desired, install additional options - a second radio tape recorder, steering wheel control, USB and bluetooth adapter.
👑Popular radio tape recorders👑
Native and non-standard receivers
The so-called standard models are installed on the machines directly at the factory. If you want to replace, update such an audio device, you have two ways:
- Buying a similar standard model and installing it in place of the previous one. The disadvantage of this method is the unreasonably high price of the music player. If you find a supposedly low-cost head unit, most likely you are in front of a Chinese fake, which does not impress with either reliability or sound quality.
- Purchase of a universal model, for which you will need to purchase a transition frame, which will cover all unnecessary holes on the panel, because the sizes of audio devices differ. For the most part, the dimensions of the standard radio tape recorders are 10x20 cm. To find an adapter specifically for your car, try making inquiries in online markets like "adapter frame for Toyota" or "Ford".
- The best alignment of events - the car has a "chip", to which everything you need is correctly connected (wires, speakers, antennas). How to connect the radio correctly? You just have to connect audio equipment to the chip and use it.
- There are wires, but the jacks of the turntable do not come with a TC plug. How to connect the Pioneer radio tape recorder in this case? We need a special. ISO adapter or you will need to twist the necessary cables yourself.
- No wiring output or the necessary work was done incorrectly. For example, how to connect a Sony radio tape recorder? Everything is done independently from the very beginning - it is worth starting the procedure if you have the appropriate experience. Otherwise, you should trust the technical center.
- Radio tape recorder.
- Postings.
- Speakers.
- A stationery knife or other tool with which you will bare the wires.
- Insulating tape.
- Fuse 10-15A + connector.
- Batteries of the "crown" variety.
- Control lamps or multimeters.
- Black (GND): - batteries.
- Yellow (BAT): + batteries.
- Red (ACC): + ignition locks.
- White (FL): Front left speaker cable. On the minuses - a strip.
- Gray (FR): Front right speaker cable.
- Green (RL): Rear left speaker cable.
- Lilac (RR): Rear right speaker cable.
- Buy only 100% oxygen-free copper with silicone insulation.
- The yellow and black cables are power cables. Check that their cross section is larger than 2.5 mm.
- For red wiring and cables to the speakers, a cross section of 1.2 mm is sufficient.
- Looking for how to connect a radio (China)? Don't buy cords with twists - it's best if they are not available. Twisting builds up excessive resistance, which is bad for both the volume and the clarity of the sound.
- To avoid confusion, remember to “bite off” the remaining portions of the cables as soon as the connector is connected to the audio device.
- If the wires do not match, they are called with a multimeter or tester to determine the polarity. There is also a "handicraft" check by means of a 9 volt battery: wiring is connected to it, then they observe the change in the diffuser: it moves out - the polarity is correct, no - it needs to be corrected. Remember to label each cable.
- All connection points must be carefully soldered and insulated.
- Black cords are for - batteries, red - for + ignition locks and yellow - for - batteries.
- Connect the black and yellow cord to the battery - for good sound.
- Do not forget to install a fuse at a distance of about 40 cm - the smallest value for it is 10 A.
- Red cords - into the network, which is powered after turning the key.
- When analyzing how to connect the radio tape recorder to the power supply, please note: if you connect both the red and yellow cords to the + batteries at the same time, your music player will be autonomous from the ignition, but it will start to consume a lot of charge.
- If you misidentified the polarity, something terrible will not happen: the main thing is not to confuse it with the mass.
- As for the speakers of the audio system, you will find two terminals there: the narrow one will be a minus, and the large one will be a plus. This is also true for those looking for how to connect a Chinese Android radio.
- Expose the cables with a knife, removing the insulation from them, placing them so that a short circuit does not happen.
- Attach the first output of a multimeter tester or control light bulb to the ground (car body), and with the other output, be sure to sequentially, touch each of the stripped wires. If the lamp lights up, if the voltage on the multimeter rises - + is found.
- Plus, twist with yellow wire from the radio, wrap it with insulating tape, or heat shrink. Here you need a 10-15 A fuse.
- We continue to analyze how to connect the Hyundai radio tape recorder and other car models. Then you need to find the + ignition switch. It is not more difficult here: turn the lock to "on" and use a multimeter tester to find the required wire in the same way. It needs to be connected to the crimson cable of the turntable (and not insulated yet).
- This instruction is also for you if you do not know how to connect a Skoda radio tape recorder. Find the mass: disconnect the control light from the car body and connect with the last twist. Now you need to serially connect the second terminal of the multimeter tester with the remaining cables - where voltage appears, there will be mass. Its already - to the black cord.
- It remains to insulate the cables in black and scarlet colors. If all is well, then you can connect the player - its screen will light up.
- Now it's the speaker turn. You should have 10 unconnected cables: eight for the speakers, one for the antenna, and one for powering the antenna. This is also true for the instructions "how to connect a Ford Focus radio."
- The cords for the antenna come in pairs, but they are not always marked correctly - this is where the battery helps. Hook it to the first pair of cables and listen carefully to which speaker snaps into place.
- Look at the “body” of the speaker itself by reconnecting the batteries to the cord. If it goes forward, the polarity is correct.
- Drivers want to know how to connect a Volkswagen car radio. According to the scheme, screw + to +, and - to -. Take due care in determining the correct polarity so that you do not suffer from poor sound quality later.
- Check and connect all the speakers in the same way. Start with front left, then back left, back right, and finally front right.
- If you are listening to the radio, connect the remaining two wires.
- Pull the permanent + from the battery with a 2.5-4mm wire. Remember to install a 10-15 A fuse.
- Look for a cord under the panel where the multimeter will indicate + when the ignition is turned on. It is from there that you need to pull the cable to the + audio device, which is responsible for turning it on. The same guide is on how to connect a Honda radio.
- Route the ground cable and secure to the vehicle body.
- Place the speakers in the standard zones, lay the wires, remembering the polarity.
- Attach the antenna.
- Get an adapter cord: a plug at one end, like a headphone, and at the other, a tulip branch.
- Connect the amplifier to the radio, connect the power supply contacts of both the amplifier and the player.
- Connect the connectors with the interconnect cable.
- Connect the speakers to the first radio tape recorder according to the recommendations indicated above.
- Now is the time to remember about the second radio tape recorder - connect it to the first one using the AUX adapter. How to connect two radios? "Tulip" is connected to the line-out of the new acoustics.
- multi-wheel;
- music player;
- two ISO adapters;
- antenna adapter;
- an adapter for the buttons on the wheel, which will combine them with the original turntable.
- The blue and lilac cables are responsible for increasing the sound volume, switching between songs, FM stations.
- Green and orange cables - volume down, transition between stations and tracks.
- The red cord is voltage.
- Black and gray are mass.
- Purchase the necessary adapter for your music player model at any electronics store or online store.
- Now let's see how to connect the USB cable to the radio. Pull the radio out of the compartment, turn the back towards you and disconnect the connector of the disc player.
- Connect the adapter to the vacated connector. The radio tape recorder will "decide" that you just changed the player: just like from a disk, it will read MP3 from a flash drive or from a phone.
Three options for connecting the radio to the car
Today, the auto industry produces a wide variety of car models, however, all methods of installing music players for them are possibly limited to three:
Read also: Best wireless headphones of this year
What is required to connect the radio?
If you decide to connect the device yourself (for example, you are looking for how to connect a Pioneer radio tape recorder), you definitely need the following:
Postings: important
Are you wondering how to connect a Chinese radio tape recorder? In fact, the connection here is essentially the connection of the necessary wires.
Having considered them, you will notice that each has its own color and markings - its own meaning:
Read also: Rating of the best headphones for gaming
Many people are interested in how to connect a radio "Pioneer" in the car. All work begins with the purchase of wires:
👑Popular budget recorders👑
In your work, remember the important advice from experts:
Connection diagrams of radio tape recorders
Universal guide for connecting a car music player:
Connection to vehicle with audio preparation
If there are "chips" with connectors, and the speakers are in the standard zones, you can easily cope with the installation of the player yourself. Often, audio preparation is an additional option when selling a new car, which is sometimes abandoned in order to buy a cheaper car.
If the vehicle has such an option, you just need to purchase an adapter between the player and the connectors. They are available in car audio stores, on the famous AliExpress. How to connect a head unit? You connect it through adapters, set it in place - and you start testing the sound.
Read also: Best headphones with AliExpress / span>
Connecting a radio tape recorder to the place of an old player
If the device was standard and you purchased a regular one again, then the diagram resembles the previous one. In a different situation, you will have to, by removing the battery terminal, cut off the connectors of the old audio device. And how to connect a Ford radio, for example? There are several wires in front of you:
How to connect a Chevrolet radio? Recall that the instruction is universal.
Connecting to a vehicle where there is no player (or is installed incorrectly)
Are you going to learn how to connect a Toyota radio tape recorder? The main difficulty is that you will have to pull the wires yourself:
Accordingly, this is the answer to the query "How to connect a Renault radio."
Read also: Top headphone manufacturers
Special cases of connecting radio tape recorders
In conclusion, we will consider the main issues of interest when connecting music players.
Two radio tape recorders
Let's figure out how to connect 2 radio tape recorders. The simplest way for two loudspeakers is via the AUX input:
Connecting the radio to the steering wheel
Many are attracted by the ability to control music playback from the steering wheel of their car. But how do you connect the radio to the steering wheel? If it's not standard, you should stock up on the following:
It is important to know how to connect the wires to the radio. Pay attention to the following during the procedure:
Connecting the radio to USB
To be able to connect USB-drives, smartphones to a radio tape recorder that was not originally intended for this, you can go the simplest way - install a special USB-adapter. This is done according to the scheme:
Bluetooth connection
Another convenient way to connect a radio tape recorder with external media is a bluetooth connection. If your player does not have a Bluetooth module, you can purchase a wireless adapter, small and compact, resembling a USB flash drive. This device is connected via a USB cable, activated according to the instructions. It's pretty easy to figure out how to connect a radio tape recorder via bluetooth. You just need to activate it on your phone, select an adapter from the list of available devices, and connect to it. In some cases, you need to enter a pin-code - the numbers are indicated in the instructions for the wireless "adapter".
